fbpx
 
Get the Most Mileage From Your Vehicle Wrap

Care for Your Vehicle Wrap

Care for Your Vehicle Wrap

How To Care for Your Vehicle Wrap and Vinyl Graphics

Source: 3M Instruction Bulletin 6.5
Click here to download the entire bulletin from 3M (pdf format).

For Cleaning Graphics with an Overlaminate Film

Use a cleaner designed for high-quality painted surfaces. Your cleaner should be wet, nonabrasive, without strong solvents, and that has a pH value between 3 and 11 (neither strongly acidic nor strongly alkaline).

For Cleaning Graphics with an Overprint Clear

Use a cleaner designed for high-quality painted surfaces. Your cleaner should be wet, nonabrasive, without strong solvents, and that has a pH value between 3 and 11 (neither strongly acidic nor strongly alkaline).

Power Washing Exterior Graphics

Not Recommended Nor Covered By Redline Design Warranty

Use a wet, nonabrasive that contains NO solvents and NO alcohol and has a pH value between 3 and 11 (neither strongly acidic nor strongly alkaline.)

Power Washing Exterior Graphics

Not Recommended Nor Covered By Redline Design Warranty

This step is from the 3M Bulletin, but is not recommend nor covered by Designer Wraps Warranty – period! Power wash AT YOUR OWN RISK!

Power washing, or pressure washing, may be used. However, aggressive washing can damage the vinyl film.

Two common types of damage are:

  • Excessive pressure during power washing can damage the graphic by allowing water to get underneath the vinyl film.
  • Water lessens the adhesion of the graphic to the substrate allowing the vinyl film to lift or curl.

These problems are magnified by wind. This is a critical problem for perforated window graphic film.

Caution: Loose graphics could tear away from a moving vehicle or from a building and cause an obstruction to motorists and pedestrians. After washing, check all the vinyl film carefully for edge lifting and repair, remove or replace any damaged film.

To avoid edge lifting or other damage to the graphics, follow these important steps:

  • Use a spray nozzle with a 40 wide spray pattern.
  • Be sure the spray nozzle includes a nozzle protector (tip guard).
  • Use a pressure of 2000 psi or less.
  • If the system is heated, limit the water temperature to 180° F or less.
  • Hold nozzle at least 12 inches (300 mm) away from and perpendicular (90° +/- 10) to the graphic.
  • Do not direct the water stream at a sharp angle to the edge of the graphic.

Caution: To reduce the risk of serious injury from high pressure spray:

  • Do not place your hand or body near the nozzle or the spray.
  • Do not direct the spray toward anyone else.

Automatic Brush Washing

Not Recommended Nor Covered By Redline Design Warranty

This step is from the 3M Bulletin, but is not recommend nor covered by Redline Design Warranty – period! Automatic Brush Wash AT YOUR OWN RISK!

Automatic brush washing may be used, but keep these two points in mind:

  • Brushes can catch a loose edge of the graphic and cause further damage to the vinyl film.
  • Brushes can dull the finish of the vinyl film.

Hand Washing Exterior Graphics

  1. Flush the graphic with clean water to remove loose dirt particles. A trigger-type hose nozzle is convenient for this purpose.
  2. Use a mild liquid detergent and water solution and wash the graphic with a soft brush, rag or sponge.
    1. Wash thoroughly from the top down.
    2. Avoid abrading the graphic by unnecessary scrubbing.
    3. After applying the cleaning solution, keep a steady stream of water flowing on the graphic to wash away dirt particles.
  3. Rinse the entire film thoroughly with clean water. Allow graphic to dry naturally.

Removing Difficult Contaminants

  1. To remove tar, oil, diesel smut or bituminous material:
    1. Wipe with a rag dampened with kerosene, mineral spirits, heptane, or VM & P naphtha. Do not use other solvents.
    2. Wash immediately with detergent and water, and then rinse with clean water.
  2. To remove pollen and fungus:
    1. Wash the graphic with a 3% to 5% sodium hypochlorite (full-strength household bleach) solution or mild liquid detergent and water.
    2. Rinse with clean water immediately.
  3. To remove crayon, lipstick, or similar materials:
    1. Select an appropriate solvent and test it in an inconspicuous area to ensure it removes the contaminant without damaging the graphic.
    2. Wash immediately with mild liquid detergent and water, and then rinse with clean water.

Hand Washing Interior Graphics

  1. Use a mild liquid detergent and water solution and wash the graphic with a soft brush, rag, or sponge.
    1. Wash graphic thoroughly from the top down.
    2. Avoid abrading the graphic by unnecessary scrubbing.
    3.  
  2. Wipe the graphic with a water-soaked brush, rag or sponge to wash away the detergent and dirt.
  3. Dry the graphic with clean toweling.
  4. Refer to Removing Difficult Contaminants, above, if necessary.

Graphic Repair

Sometimes graphic damage can be repaired; however, repaired graphics are not warranted. These procedures are for information only.

Damage to Face of Graphics

  1. Trim and clean loose areas of film before patching.
  2. Use a film or sheeting with pressure-sensitive adhesive, if possible. The color or gloss of the new material will vary slightly due to weathering of the original material.
  3. Cut the patches so they overlap all sides of the damaged area by at least 1/4 inch (6.4 mm).
  4. Position the patch over the damaged area.
  5. Hold in place at the top with a strip of Scotch Masking Tape.
  6. Remove the paper liner.
  7. Squeegee firmly into place using a plastic applicator.
  8. Use heat such as from a heat gun to heat all edges of the patch, and then re-squeegee all edges.

Edge Damage

  1.  
    1. Trim loose edges back to the point where the adhesive is firmly adhered to the substrate.
    2. Apply edge sealing, if desired. Edge sealant may help prevent further damage if the lifting is caused by aggressive washing conditions.

Redline Design uses other vinyl manufacture films, but in general the above care instructions work for all vinyl types.

 

Call or email us if you have any questions.